Fortress Technologies ecure Wireless Access Bridge Manual de usuario Pagina 34
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Fortress Bridge: Configuration
24
NOTE: The IP ad-
dress you assign
must be unique on the
network.
To reconfigure Bridge LAN settings:
1 Log on to the Bridge GUI admin account and select LAN
SETTINGS from the menu on the left.
2 On the LAN SETTINGS screen, make your changes to the
relevant field(s). These include:
CAUTION: If the
WAN port is pro-
viding the link to an un-
encrypted interface,
such as a cable or DSL
modem or satellite u p-
link, the WAN port
must reside in the net-
work’s unen cry pte d
zone.
Host name - a descriptive name for the Bridge
LAN IP address - the network address of the Bridge
LAN Subnet mask - the correct subnet mask for the
Bridge
Default gateway - the IP address of the default gateway
STP - enables/disables Spanning Tree Protocol
(enabled by default)
WAN Port - configures the WAN port to reside in either
the encrypted zone of the Bridge-secured network or in
the unencrypted zone.
NOTE: If you are
using Firefox’s
tabbed browsing, you
must close the active
browser instance com-
pletely—not just Bridge
GUI’s active tab in the
browser.
Click Apply.
3 Click OK on the system prompt that instructs you to reboot.
4 Follow the instructions in Section 4.7 to reboot the Bridge.
You must use a new instance of the browser (and the new
IP address, if it has changed) when you next access the
Bridge’s management interface.
3.3 Radio Settings
NOTE: Additional
radio interface set-
tings can be configured
through
VIRTUAL ACCESS
POINT SETTINGS (accessi-
ble from the
INTERFACES
screen, Section 3.3.4)
and through the Con-
troller CLI (sections
6.4.3 an d 6. 7 ) .
The Fortress Bridge is equipped with two, independent internal
radios, the basic configuration settings for which appear on the
RADIO SETTINGS screen. The default settings are shown below.
- Secure Wireless 1
- Access Bridge 1
- Fortress Bridge 3
- Table of Contents 5
- Configuration 21 6
- Administration 52 7
- Command-Line Interface 80 8
- Chapter 1 11
- Introduction 11
- 1.2 Network Security Overview 12
- 1.3.3 System Components 13
- 1.3.4 Operating Modes 13
- 1.3.5 Deployment Options 14
- 1.4 This Document 15
- Chapter 2 16
- Installation 16
- 2.2 Preparation 17
- 2.2.2 Preparing the Network 18
- 2.2.3 Port Locations 18
- WARNING: The 19
- WARNING: To 19
- WARNING: If the 20
- 2.3 Installation Instructions 21
- 2.4 Outdoor Installation 21
- Clear for WAN Port 23
- CAUTION: The 24
- Non-Root, and click Apply 25
- 2.4.3 Weatherizing the Bridge 26
- 2.5 Indoor Installation 29
- 2.5.2 Configuring the Bridge 30
- Chapter 3 31
- Configuration 31
- 3.2 LAN Settings 32
- Multicast field 33
- 3.3 Radio Settings 34
- ANT1); Radio 2 uses an 35
- CAUTION: 36
- Distance setting on the 37
- Preamble setting of Short 37
- Preamble setting of Long 37
- 100 milliseconds 38
- AP radio mode on the VIRTUAL 40
- Edit button for each VAP 40
- RADIO SETTINGS screen.) 41
- Cleartext Security 42
- Fortress Security 42
- Open WEP and Shared WEP 42
- 802.1X Security 43
- WPA-PSK or WPA2-PSK be used 44
- WPA-Mixed-PSK) 44
- Edit button for 44
- 3.5 Bridge Passwords 46
- For security 47
- Normal operating mode meet 48
- 3.6.2 Secure Shell Access 49
- 3.6.3 Encryption Algorithm 49
- 3.6.4 Re-keying Interval 50
- 3.6.5 Access ID 50
- Global and Default Settings 51
- AUTHENTI 52
- CATION SETTINGS to point 52
- Mode field 52
- section of the 54
- Auth Mode, ensure 54
- 3.7 Blackout Mode 57
- 3.8 System Date and Time 58
- 3.10 Front-Panel Operation 59
- BLACKOUT MODE: Disabled), or 60
- Chapter 4 62
- Administration 62
- Allow. Such a device 63
- To edit a device: 64
- 4.2 User Authentication 65
- Local au 66
- To add a user: 67
- To edit a user account: 67
- To delete a user account: 68
- 4.3 Trusted Devices 69
- 4.3.1 Editing Trusted Devices 70
- 4.4 SNMP Settings 71
- 4.5 Backing Up and Restoring 72
- FIPS operating mode 73
- 4.6.1 Viewing 75
- Current Software Version 75
- Performing 76
- 4.7 Rebooting the Bridge 77
- Chapter 5 78
- Monitoring and Diagnostics 78
- 5.1.1 Traffic Statistics 79
- 5.1.2 Interface Statistics 79
- 5.2 Tracking 80
- 5.3 AP Associations 82
- 5.4 View Log 83
- 5.5 Diagnostics 85
- HOST MAC DATABASE: 86
- HOST MAC DATABASE button 86
- 5.6 Front-Panel Indicators 87
- 5.6.2 Radio LEDs 88
- 5.6.3 Port LEDs 89
- Chapter 6 90
- Command-Line Interface 90
- bits per second: 9600 91
- data bits: 8 91
- parity: none 91
- stop bits: 1 91
- hardware flow control: none 91
- 6.2 Getting Help in the CLI 92
- 6.3 Command Syntax 93
- 6.4.1 LAN Settings in the CLI 94
- Enter↵, to display the 95
- NOTE: The Bridge 96
- ANT1), while 96
- NOTE: If you are 96
- Enter↵ to leave the 96
- NOTE: Because 97
- Enter↵ to 99
- NOTE: Pa s s wo r d s 101
- NOTE: Usernames 101
- NOTE: Yo u c a n 102
- CAUTION: For se 103
- CAUTION: If you 104
- NOTE: Disabling 104
- NOTE: The 105
- Enter↵ to save them 105
- NOTE: Tr u s t e d D e 110
- CAUTION: Specify 110
- NOTE: You cannot 110
- FIPS op 110
- NOTE: The term 112
- 6.6.7 Pinging a Device 114
- 6.6.8 Tracing a Packet Route 114
- NOTE: Wir e le s s 115
- NOTE: You cannot 115
- Deployment with SAC 116
- 10.0.0.0–10.255.255.255 118
- 172.16.0.0–172.31.255.255 118
- 192.168.0.0–192.168.255.255 118
- <serialnumber> 123
- Chapter 7 124
- Specifications 124
- 7.1.4 Compliance 125
- 7.1.5 Logical Interfaces 125
- Chapter 8 127
- Troubleshooting 127
- Failed to decrypt 128
- Glossary 138
- Fortress : Glossary 139
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales